Blog

How-to

How to Start a Dirt Bike With Kick Start

Learn the correct technique to kick start a dirt bike, from cold-start steps to common mistakes that flood the engine or cause a kickback injury.

7 min read

Starting a dirt bike with a kick starter is about rhythm and position, not brute force. Find top dead center on the compression stroke, then deliver one firm, full-length kick with your body weight behind it, using the right choke and throttle setting for whether the engine is cold or warm.

Kick starting looks simple until you're standing next to a bike that won't fire.

Before You Kick: Quick Pre-Start Checks

Run through these in under a minute every time, especially if the bike has been sitting.

  • Fuel petcock: open (usually marked ON, with RES for reserve).
  • Kill switch: in the run position, not killed.
  • Fuel in the tank: obvious, but worth checking first. If the bike has sat for weeks or months, old fuel can also be the culprit. See our fuel stabilizer guide.
  • Choke: on for a cold start, off if the engine is already warm, if your bike has a choke. Fuel-injected bikes and some carbureted bikes use a different cold-start control, so follow your bike's specified procedure instead of assuming a choke lever is present.
  • Transmission in neutral: find neutral before you start kicking.

Safety: dirt bikes don't have a sidestand that supports kicking from the saddle the way street bikes do on some models, so most riders kick while standing beside the bike or straddling it with both feet down. Keep your foot clear of the kicker's swing path on the return stroke, wear boots, and never kick a bike that's in gear with the rear wheel against something or someone.

Finding Top Dead Center

This is the step most new riders skip, and it's the difference between a bike that starts easily and one that kicks back hard or just won't fire.

  1. Shift to neutral and confirm it by rolling the bike slightly, you should feel no drag from the drivetrain.
  2. With your foot on the kicker and clear of the lever's return path, slowly press down with your boot until you feel resistance build. On some bikes that resistance can help you feel the compression stroke, but it isn't reliable on every engine, so follow the starting-position procedure for your exact bike.
  3. On many dirt bikes you'll feel the lever settle into a spot just past the hardest point, roughly a few degrees past top dead center. That's your kick-off position, but it varies depending on the bike's decompression system, so check your owner's manual for the correct starting position on your exact model.
  4. Some bikes have a mark on the kick lever or a slight notch you can feel. If your bike came with an owner's manual, it may describe the exact feel for your model.

Use the starting-position procedure for your bike and make a firm, complete kick. If the lever repeatedly kicks back, stop and check the specified procedure, then have a mechanic investigate a possible ignition or decompression fault.

The Actual Kick

Once you've found the compression point:

  1. Stand with your weight over the footpeg on the kick side, or sit with your kicking leg positioned to drive straight down through the lever.
  2. With the engine positioned as specified for your bike, let the kick lever return fully to the top before you kick.
  3. Kick down smoothly but firmly through the entire travel of the lever, don't stab at it halfway.
  4. Let the lever return on its own, don't ride it back down with your foot, and don't let it snap back uncontrolled either.

If it hasn't fired after five or six clean kicks, stop and troubleshoot rather than repeating the same thing harder.

Cold Start vs Warm Start Settings

Safety: fuel system adjustments like choke and throttle are low risk on their own, but always do this with the bike on firm, level ground and the area clear, since a bike that fires unexpectedly in gear can lurch forward.

The table below reflects typical settings for carbureted dirt bikes with a choke lever. If your bike is fuel injected, or uses a different cold-start control such as a fast-idle lever or an automatic enrichment circuit, follow the cold-start procedure specified for your exact bike instead.

Condition Choke Throttle Notes
Cold engine, first start of the day On (full choke) Closed, don't touch it Let it idle 15 to 30 seconds once it fires, then ease choke off gradually
Cold engine, cool weather On Closed May need a few extra kicks before it catches
Warm engine, restarting after a short stop Off Closed, or barely cracked Choke on a warm engine usually floods it
Hot engine after a stall on the trail Off Crack throttle slightly A fully open throttle with no choke is closer to the flooded-engine procedure below

Two-strokes tend to be more sensitive to choke position than four-strokes, and will foul a plug quickly if you leave the choke on too long after startup. If your bike is carbureted, small adjustments at the idle circuit also affect how it behaves on kick start, covered in our idle screw adjustment guide.

If the Engine Floods

A strong raw-fuel smell after repeated starting attempts can suggest flooding, but kick resistance does not diagnose it. Pulling the plug afterward and finding it soaked with fuel is a further clue, rather than how the kick feels.

Flooded-start procedures differ between bikes, and some carbureted bikes add more fuel when you open the throttle rather than clearing it, so check the procedure for your exact bike before trying to clear a flood. On bikes where it applies, the common method is to turn the choke off completely, hold the throttle wide open, and kick through several times, which admits more air while you attempt to restart the engine. If the engine catches, close the throttle immediately to avoid revving too high. This method is not universal, and fuel-injected bikes often use a different procedure, so confirm it for your bike first.

Safety: before pulling a spark plug to check for flooding, switch off the ignition and let the engine and exhaust cool. A fuel-wet plug and spilled fuel are both fire hazards, so keep the plug, your tools, and the area clear of sparks and open flames while you work.

If it still won't start after this, pull the spark plug and check if it's wet with fuel. If so, dry the plug off or swap it, and try again with the choke off.

When Kick Starting Isn't the Problem

If you've nailed the technique and the bike still won't start, the issue is usually spark, fuel delivery, or compression rather than your kicking form. If the kicker feels light and spongy with no real resistance, don't rely on a hand-felt check at the lever to confirm it, since automatic decompression can make a healthy engine feel light too. If low compression is suspected, have a proper compression or leak-down test done using the procedure for your exact bike. For a full breakdown of causes and checks, see our dirt bike troubleshooting guide.

Because kick starting technique and specs vary by model, year, and whether the bike is two-stroke or four-stroke, it helps to check what's normal for your exact bike before assuming something's broken. For questions about your own bike, MotoDoc lets you choose the make, model and year, then ask by text or voice and attach a photo of a part or a warning light.

Common Mistakes to Avoid

  • Half kicks: not completing the full stroke may not turn the engine over fast enough for it to start reliably.
  • Choke left on too long after starting: fouls plugs, especially on two-strokes.
  • Kicking in gear with the clutch not fully disengaged: the bike can lurch forward unexpectedly.
  • Ignoring your bike's specified engine starting position: can make starting harder and may increase the risk of kickback.

Get the top dead center feel right, match choke and throttle to engine temperature, and commit to a full, smooth kick every time, and most dirt bikes will start reliably without drama.

Frequently asked questions

Why won't my dirt bike start on the kick starter even though it has spark and fuel?

A proper compression or leak-down test, done with the procedure and specifications for your exact bike, is the reliable way to check for a worn piston ring, a stuck valve, or a decompression mechanism issue. Hand-felt resistance on the kicker is not a dependable substitute, especially on bikes with an automatic decompressor. Also confirm the kill switch is off and the fuel petcock is open before assuming it's a bigger problem.

Do I need to use the choke every time I kick start a dirt bike?

Only on a cold engine, and only if your bike has a choke. Fuel-injected bikes and some carbureted bikes use a different cold-start control, so check the procedure for your exact model. A warm engine that has already been run that day usually starts better with the choke off, since extra fuel can flood it. If it struggles warm, try one kick with the throttle slightly cracked instead of using choke.

Is it normal for a dirt bike to kick back hard?

A hard kickback can result from starting technique, but repeated kickback can also indicate an ignition-timing or decompression problem. Follow your bike's starting procedure and have a mechanic investigate if it persists.

Why does my dirt bike flood every time I try to kick start it?

Flooding usually comes from too much choke, too many kicks with the throttle open, or a stuck float in the carburetor. Check the flooded-start procedure for your exact bike. Do not use wide-open throttle unless that procedure calls for it. If it floods repeatedly on a bike that used to start fine, check the float needle and fuel level in the carb.

5 free questions a day

Start with a question about your bike.

Download MotoDoc — it's free to start.