Blog

How-to

How to Fix Cracked Motorcycle Fairings

Learn how to fix cracked motorcycle fairings and broken tabs with plastic welding, adhesives or fiberglass, step by step, with tools and prep tips.

8 min read

Many cracked motorcycle fairings can be repaired at home with a material-compatible weld or adhesive, but badly damaged panels and heavily loaded mounts may need replacement. The right method depends on the plastic type, the size of the crack, and whether a mounting tab has snapped off along with it.

Fairing plastic takes a beating from tip-overs, vibration, heat cycling, and over-tightened fasteners. Most cracks start at a bolt hole or tab, where stress concentrates every time the bike hits a bump. Fixing it properly means addressing why it cracked, not just filling the gap.

Identify the Plastic Before You Start

Most street fairings are ABS, polypropylene (PP), or occasionally fiberglass or carbon composite on higher end bikes. The repair method that works on one will fail on another, so this step matters more than people expect.

Look for a recycling-style code stamped into the inside of the panel, often near a mounting tab: ABS, PP, or PP/EPDM are common. If you cannot find a code, check for markings elsewhere on the panel, such as near the fasteners or on the inner surface, or look up the material through the panel manufacturer's information before selecting a repair product. Fiberglass panels feel more rigid and show visible woven fibers if you look closely at a broken edge.

Knowing the plastic tells you which adhesive or welding rod to buy. ABS plastic welding rods and ABS-specific adhesives work on ABS panels. Polypropylene needs a PP rod or a flexible PP-rated adhesive, since standard epoxy does not bond well to polypropylene without a plastic primer or adhesion promoter made for that purpose.

Tools and Materials You Will Need

  • Plastic welder (soldering iron style with ABS or PP rods) or a two-part structural plastic epoxy
  • 80 to 220 grit sandpaper
  • Isopropyl alcohol or plastic-safe degreaser
  • Plastic adhesion promoter (for polypropylene)
  • Fiberglass cloth or mesh and epoxy resin, or a plastic mesh/staple kit, for backing reinforcement
  • Masking tape, clamps or zip ties to hold pieces in place
  • Body filler rated for flexible plastics, for the final smoothing
  • Primer and paint matched to your fairing color

You do not need a full body shop setup. Compare the cost of tools and finishing materials with the cost of a replacement panel before choosing a method, and most of this work can be done on a workbench with the fairing removed from the bike.

Step-by-Step: Fixing a Cracked Fairing

Remove and Prep the Panel

Take the fairing off the bike. Working on a flat surface gives you better access to both sides of the crack, which matters because the strongest repairs reinforce from the back, not just the visible side.

Clean the area with soap and water, then wipe it down with isopropyl alcohol to remove wax, road grime, and mold-release residue. Sand both sides of the crack with 80 to 120 grit paper to rough up the surface about 20 to 30 mm (roughly 1 inch) beyond each end of the crack. This prepares the surrounding surface for the repair and helps reveal the full extent of the crack.

Drill a tiny stop hole, about 1.5 to 2 mm (around 1/16 inch), at each very end of the crack. A carefully placed stop hole may help limit the crack from creeping further, but it is not a substitute for a material-compatible repair of the joint, and a poorly placed hole can become another stress point of its own. If the crack is tied to a mounting bolt or bracket, any stress from an over-tightened fastener or missing grommet must be corrected too, or the crack is likely to return.

Weld, Glue, or Fiberglass the Crack

For ABS or PP plastic welding: set the soldering-iron-style welder to the temperature recommended for your plastic type (check the welder's instructions, since settings vary by brand and rod type), then run the plastic rod along the crack from the back side first, melting it into the joint. Let it cool fully, flip the panel, and repeat on the front side, filling flush with the surrounding surface.

For adhesive repair: apply the two-part epoxy to both sanded surfaces, press them together, and hold with tape or clamps per the product's cure time. For polypropylene, use an adhesive rated for PP and follow its surface-preparation instructions. Apply a compatible adhesion promoter only if the adhesive manufacturer specifies one.

For larger cracks or stress points near a mounting boss: cut a patch of fiberglass cloth slightly larger than the damaged area, mix epoxy resin, and laminate it over the back of the crack. This spreads load across a wider area, but fiberglass cloth with ordinary epoxy resin can bond poorly to polypropylene and may be a poor choice for a highly flexible or heat-exposed panel. Use this method only with cloth and resin systems the manufacturer confirms are compatible with your plastic type. For polypropylene, a compatible plastic weld or adhesive with a mesh or plastic patch backing is a more reliable reinforcement.

Safety: keep plastic welding tools and solvents away from the fuel tank, fuel lines, and wiring harness, and never work near an open fuel cap or spilled gasoline. If the crack sits right next to a headlight mount, turn signal bracket, or any wiring that routes through the fairing, double check nothing is pinched or exposed once the repair is done, since a loose wire chafing on sharp plastic can cause an electrical short.

Fixing Broken Fairing Tabs

Broken tabs are the most common fairing complaint, and they fail differently than a flat crack because they carry constant vibration and clamping load from the bolt.

Clean and sand both broken faces the same way as a crack repair. Because tabs snap under repeated flex, gluing or welding the original break alone is rarely enough. Reinforce it:

  1. Tack the tab back in its original position with a small dab of adhesive or a quick weld pass to hold alignment.
  2. Confirm that fiberglass cloth and resin are compatible with your panel material before using them on the tab, then laminate a strip across the back of the tab and extending onto the solid panel around it. For polypropylene, use a compatible weld or adhesive reinforced with a plastic patch or mesh made for that plastic instead of ordinary fiberglass resin.
  3. For a tab that is missing a chunk, build up the shape with a welding rod matching the identified plastic, or a putty or adhesive whose manufacturer confirms compatibility with that plastic and with use at a loaded mounting tab, then sand to match the original profile once cured.
  4. Let everything cure fully before test-fitting the bolt. Do not force a bolt into a tab that is still soft from a same-day repair.

If a tab keeps re-breaking even after reinforcement, the real cause is often an over-tightened fastener or a missing rubber grommet that used to cushion the joint. Check that the bolt has the correct grommet or well-nut in place and is not bottoming out hard against the plastic.

Finishing: Filler, Sanding and Paint

Once the structural repair has cured, apply a thin layer of flexible plastic body filler over the repaired area to smooth any unevenness. Sand progressively from 120 up through 400 or 600 grit for a smooth finish ready for primer.

Use a plastic-specific primer, since standard automotive primer can crack or peel off flexible fairing plastic over time. Color-match paint and clear coat as you would for any bodywork repair, and give full cure time before reinstalling the panel and riding in rain or direct sun.

For an electrical issue uncovered during fairing removal, such as a cracked headlight bucket or a chafed wire near a broken tab, damaged wiring must be repaired before the bike is ridden again. Safety: if you cannot identify a wire, confirm a connector, or repair the damage safely yourself, have a qualified mechanic check it, since a chafed or exposed wire near a fairing mount can create a dangerous electrical fault. For help tracing a wire or identifying a connector, see this guide on how to read a motorcycle wiring diagram. For questions about your own bike, MotoDoc lets you choose the make, model and year, then ask by text or voice and attach a photo of a part or a warning light.

When to Replace Instead of Repair

Repair makes sense for cracks, chips, small holes, and broken tabs on otherwise intact panels. Replacement is the better call when the fairing is shattered into multiple pieces, warped from heat exposure near the exhaust, or missing so much material that reinforcing it would leave a weak, flexible patch that will crack again under normal riding vibration. If you are unsure whether a panel near the steering head or front fork is structurally sound enough to keep riding on, have a qualified mechanic inspect it before putting the bike back on the road.

Frequently asked questions

Can a cracked motorcycle fairing be fixed permanently?

A well-prepared, material-compatible repair can hold up in normal use, but a heavily loaded or repeatedly cracking mount may need a replacement panel. The repair holds up best if you prep the surface fully and reinforce the back, not just fill the crack on top.

What is the best glue for plastic motorcycle fairings?

Choose a structural adhesive specifically rated for your fairing plastic and the joint's expected flex, and check its preparation instructions, particularly for polypropylene. Ordinary super glue is generally a poor choice for a vibrating mounting tab, so check the label for the plastic type your fairing is made of before buying.

How do you fix a broken tab on a motorcycle fairing?

Clean and rough up the broken tab and matching surface. Reattach and reinforce it using a method rated for the identified plastic. If material is missing, rebuild the tab with a matching welding rod or a filler whose manufacturer confirms it is suitable for that plastic and a loaded mounting tab. Broken tabs take repeated stress from vibration, so always reinforce rather than just gluing the original break.

Is it cheaper to repair or replace a motorcycle fairing?

Repair may cost less for minor damage like small cracks or broken tabs, but compare the cost of materials, paint and labour with the cost of a replacement panel before deciding. Replacement is often the safer choice when the plastic is badly shattered, warped from heat, missing large sections, or when a crack keeps returning at a stressed mounting point.

5 free questions a day

Start with a question about your bike.

Download MotoDoc — it's free to start.